Developages - Development and Technology Blog

Julie188 writes “Slow-moving ocean and river currents could be a new, reliable and affordable alternative energy source. A University of Michigan engineer, Michael Bernitsas, has made a machine that works like a fish to turn potentially destructive vibrations in fluid flows into clean, renewable power. This is is the first known device that could harness energy from most of the water currents around the globe because it works in flows moving slower than 2 knots (about 2.3 miles per hour). Most of the Earth’s currents are slower than 3 knots. Turbines and water mills need an average of 5 or 6 knots to operate efficiently. Further details and a few brief movies of the technology are available, as well as a video explanation by Professor Bernitsas himself.”

Read more of this story at Slashdot.

Original post by Soulskill

An anonymous reader writes “Today, more than 40 percent of all homes in the United States contain at least one video game console. Recognizing that all that gaming could add up to serious demand for electricity, NRDC and Ecos Consulting performed the first ever comprehensive study on the energy use of video game consoles and found that they consumed an estimated 16 billion kilowatt-hours per year — roughly equal to the annual electricity use of the city of San Diego. Through the incorporation of more user-friendly power management features, we could save approximately 11 billion kWh of electricity per year, cut our nation’s electricity bill by more than $1 billion per year, and avoid emissions of more than 7 million tons of CO2 each year. In this November 2008 issue paper, NRDC provides recommendations for users, video game console manufacturers, component suppliers and the software companies that design games for improving the efficiency of video game consoles already in homes as well as future generations of machines yet to hit the shelves.” The full report is freely downloadable as a PDF.

Read more of this story at Slashdot.

Original post by timothy

MagnetDroid writes “A startup company based in Vancouver has developed a new kind of generator that could harvest much more energy from the wind. The design could not only lower the cost of wind turbines but increase their power output by 50 percent to as much as 100 percent, in some locations. Normally, when wind speeds drop, a turbine’s engine becomes less efficient. The new engine, from ExRo Technologies, runs efficiently over a wider range of conditions. The design replaces a mechanical transmission with what amounts to an electronic one. Magnets attached to a rotating shaft create a current, but individual coils can be turned on and off electronically at different wind speeds.” The company will begin field-testing a small, 5KW wind turbine by early next year.

Read more of this story at Slashdot.

Original post by kdawson

miller60 writes “An air conditioning technology called the ‘heat wheel′ is getting a test drive in data centers, and early adopters cite impressive reductions in their power bills. The heat wheel — also known as a rotary heat exchanger or Kyoto Cooling — is a refinement of cooling systems using outside air. Rather than introducing exterior air directly into the server room (the air economization we discussed recently), the heat wheel briefly mixes the outside air and exhaust air to create an air-to-air heat exchanger. A data center in the Netherlands using this approach only has to use chillers 11 days a year.” The article points out that the heat wheel is not new, but it hasn’t been applied to data centers until recently.

Read more of this story at Slashdot.

Original post by kdawson

Mojo Mobility Inc, a Silicon Valley-based venture firm, has developed a technology to simultaneously charge multiple mobile devices simply using a flat surface that doesn’t even to touch the charging circuitry of  mobile phones, iPods, iPhones, and other gadgetry.

While NFP (Near Field Power) is not a new concept, the non-contact charging system leverages an electromagnetic induction method. The system is composed of two coils, one for transmitting and the other for receiving electric power.

Mojo Mobility has developed a prototype sheet-type charger equipped with multiple transmitting coils. On this sheet to the right, up to four devices charged at the same time with the ability to produce 2.5W to 4W of power ..

Read

Tags: charge, electric power, electricity, gadgets, mobile phone, Mojo Mobility, Near Field Power, NFP, wireless

Related Entries
• Mobile VoIP Challenges -
  Oct 20, 2008
• Tom writes ‘iHate My iPhone Because its iDead′ -
  Jul 12, 2008
• fring Enhances Mobile IM Client with fringAdd-ons -
  Jul 01, 2008
• Nokia Ệ Comes to U.S. -
  Jun 24, 2008
• Instant Charge for Cell Phones on the Horizon? -
  May 20, 2008
• Wireless Backhaul Importance Grows -
  Mar 25, 2008
• ʪ Technologies mCUE mobile convergence softphone launches -
  Jan 07, 2008
• PackeҐ MobileTalk Launches -
  Nov 19, 2007
• Minimizing network load when routing to Ported Mobile Phone Numbers -
  Oct 17, 2007
• AT&ampT Unity brings voice minutes closer to free -
  Jan 19, 2007

TrackBacks
| Comments | Tag with del.icio.us | VoIP & Gadgets Blog Home | Permalink: Mojo Mobility Charges Gadgets Wirelessly

Copyright VoIP & Gadgets Blog

Original post by nafiz

enbody writes “The Freakonomics Blog at NYTimes.com reports on a study of Indiana energy use for daylight savings time showing an increase in energy use of 1%. ‘The dataset consists of more than 7 million observations on monthly billing data for the vast majority of households in southern Indiana for three years. Our main finding is that &mdash contrary to the policy’s intent &mdash D.S.T. increases residential electricity demand.’” Maybe that’s just from millions of coffee makers being pressed into extra duty.

Read more of this story at Slashdot.

Original post by timothy

Fluffeh alerts us to a report of a fungus that naturally produces diesel fuel, or something very close to it. “A fungus that lives inside trees in the Patagonian rain forest naturally makes a mix of hydrocarbons that bears a striking resemblance to diesel, biologists announced today. And the fungus can grow on cellulose, a major component of tree trunks, blades of grass and stalks that is the most abundant carbon-based plant material on Earth…. [T]the paper’s authors admit that the technique is far from any sort of industrial production. ‘This report presents no information on the cost-effectiveness or other details to make G. roseum an alternative fuel source,’ they write.” NPR has an interview with the fungus’s discoverer.

Read more of this story at Slashdot.

Original post by kdawson

snydeq writes “Powering down servers to conserve energy is a controversial practice that, if undertaken wisely, could greatly benefit IT in its quest to rein in energy costs in the datacenter. Though power cycling’s long-term effects on server hardware may be mythical, its effects on IT and business operations are certainly real and often detrimental. Yet, development, staging, batch processing, failover — several server environments seem like prime candidates for routine power cycling to reduce datacenter energy consumption. Under what conditions and in what environments does powering down servers seem to make the most economic and operational sense, and what tips do folks have to offer to those considering making use of the practice?”

Read more of this story at Slashdot.

Original post by timothy

Now you no longer have to worry about the tragic and unthinkable happening — losing power to your iPhone or iPod!

Brando’s iPhone/iPod Emergency Charger puts the emphasis on simplicity, portability and usefulness. (So nice!)

This compact, lightweight Emergency Charger with retractable cable can use “AA” batteries to power the Apple iPhone and iPod anytime, anywhere and at the time that you need it most. 

It features anytime, anywhere instant charging, and it’s retractable cable makes it very easy to carry.

But remember, this is just for emergency use only and doesn’t replace your A/C power charger to make your iPhone or iPod 100% charged.

Cost: $10.00

mobile.brando.com.hk

Tags: brando, iphone, ipod

Related Entries
• You Can Buy Gadgets Everywhere! -
  Aug 28, 2008
• Woz: The Engineer Behind the Apple -
  Aug 26, 2008
• What’s in Your Back-to-School Pack? -
  Aug 27, 2008
• Amazon’s Special MP3 Deals — Indeed! -
  Aug 18, 2008
• Microsoft Debuts Its Surface 30″ Interactive Screen at Sheraton -
  Aug 20, 2008
• Malware & Hackers Heading to Mac Land -
  Jul 23, 2008
• Apple iPhone 2.0: Twice as Much for Half as Much -
  Jun 09, 2008
• Looking to Predict Apple’s Future -
  May 22, 2008
• Free iPhone if… -
  Jun 29, 2007
• Apple and Cisco make iPhone love -
  Feb 22, 2007

TrackBacks
| Comments | Tag with del.icio.us | VoIP & Gadgets Blog Home | Permalink: Very Handy iPhone & iPod Emergency Charger

Copyright VoIP & Gadgets Blog

Original post by nafiz

TrickleStar, a Hong Kong-based manufacturer, will be making the U.S. debut of the ”world-first” power-saving device. 

TrickleStar’s products address the issue of standby power consumed by PC appliances and TV accessories by stopping the flow of standby power when in “standby” mode. 

The TrickleStar PC Standby Power Saver connects to a PC via a standard USB cable and detects the power status of a PC via the USB port. When a PC is “on,” the product will switch “on” all accessory devices. Conversely, when a PC is switched “off,” it will switch “off” all accessory devices.

I like it. Let’s get some of these soon.

More at CEPro.com.

Thanks to Waynet.org for the image.

Tags: pc standby power saver, tricklestar

Related Entries

TrackBacks
| Comments | Tag with del.icio.us | VoIP & Gadgets Blog Home | Permalink: Trickle Trickle Little TrickleStar

Copyright VoIP & Gadgets Blog

Original post by nafiz

Analog Devices unveiled the new Blackfin BF51x series, the newest members of their convergent-processor family. Blackfin processors are very popular when building Asterisk-based appliances, including the Digium Asterisk Appliance AA50 and Astfin. The Blackfin convergent-processor architecture offers reduced cost, power consumption, and software complexity. Although the processor is popular in creating Asterisk appliances, it can be used for a variety of low-cost, low-power consumption required applications.

The new Blackfin processors are the BF512, BF514, BF516 and BF518. According to Analog Devices, “All are single-core convergent processors that surpass outdated, heterogenous MCU+DSP approaches in reducing part-count, system cost, board space, and power consumption. Like traditional DSPs, the BF51x processors feature high clock rates and low power dissipation per unit of processing (MMACs/mW), and like traditional MCUs, these convergent processors are OS and compiler-friendly.”

All four of the new 16-/32-bit BF51x processors are available at clock speeds up to 400 MHz (800 MMACS) and include 116 kBytes of RAM plus an optional 4 Mbits of serial (SPI) flash memory. Each also integrates Lockbox™ security for code and content protection.

The Blackfin processors on-chip integration assures easy connection to a variety of audio, video, imaging and communications peripherals and memory types. Integrated features include support for sixteen stereo I2S digital-audio channels, twelve peripheral DMA channels, and an advanced memory controller for glueless connection to multiple banks of external SDRAM, SRAM, Flash, or ROM. Each processor includes two dual-channel synchronous serial communication ports (SPORTs), a high-speed parallel peripheral interface (PPI), an I2C compatible two-wire interface (TWI), dual PC-compatible UARTs, and 2 SPI-compatible serial peripheral interface ports.

“System solutions ultimately determine how much power any particular application will consume,” said Jerry McGuire, vice president, General Purpose DSP, Analog Devices, Inc. “It’s quite intuitive that a single convergent processor with the right mix of integrated peripherals is always going to lead to lower BOM costs and power consumption than an inelegant combination of disparate processors and parts can possibly achieve. Many companies today talk about the lowest power or the highest performance. But what is important for today’s applications is the highest levels of performance at low power.”

All of the new Blackfin processors, delivering 8.5 MMACs/mW (100 MHz), include dynamic power management (DPM) functionality that lets developers match the processor’s power consumption to processing requirements during program execution. ADI pioneered the application of DPM more than seven years ago with the release of the first Blackfin processors.

The B𑍰 is the new low-cost entry point in the Blackfin processor family. The device balances performance, peripheral integration, and price, and is well suited for the most cost-sensitive applications including portable test equipment, embedded modems, biometrics, and consumer audio. All members of the Bᮋx family also include a new 3-phase PWM generation unit for inductive motor control applications and a quadrature interface for rotary encoders.

The BF514, BF516, and BF518 all extend the convergent processor family further into the portable application space with on-chip removable-storage interfaces. All three devices include Secure Digital Input Output (SDIO) for connectivity to standard flash memory and Wi-Fi cards; a power-optimized CE-ATA storage interface for small form-factor handheld and consumer electronics applications; and an embedded multimedia card (eMMC) interface for integrating mass-storage flash memory in a wide range of consumer electronics, wireless, navigation, and industrial applications.

For developers of network-connected industrial and instrumentation applications, the BF516 adds an Ethernet 10/100 MAC with Media Independent Interface (MII) and Reduced Media Independent Interface (RMII). Highly integrated for industrial, portable and VoIP applications, the BF518 Ethernet MAC supports the IEEE-1588 clock synchronization protocol for networked measurement and control systems.

An increasingly wide variety of applications are viewing the contemporary convergent-processor approach as the soundest choice for cost- and power-sensitive designs. For example, some voice-over-IP (VoIP) telephony system developers have designed in separate DSP and microcontroller chips to implement the required media and control functionality. With BF51x Blackfin processors, however, a single architecture enables full VoIP telephony functionality in a unified software development environment with faster system debugging and deployment, lower overall system cost, and the lowest possible system power demand.

“GIPS VoiceEngine media processing capabilities meet the highest requirements of VoIP equipment manufacturers and paired with Analog Devices’ Blackfin processors we can assure customers a consistently high quality VoIP experience. The performance, power and functionality profile of Blackfin is a superb fit for VoIP technology,” said Larry Golob, Senior Director Business Development, Global IP Solutions.

With the Global IP Solutions (GIPS) VoiceEngine package of VoIP software components available for Blackfin processors, and a VoIP reference platform available on uClinux, the feature-rich Blackfin family has driven down the price required to easily design and deploy a fully scalable range of VoIP telephony designs across multiple market spaces.

Pricing and Availability
The BF51x family includes the BF512 at $4.95, the BF514 at $7.75, the BF516 at $8.75 and the BF518 at $11.85. Processors are sampling immediately. All prices are based on 25,000-unit quantities.

Tags: appliance, asterisk, Astfin, BF512, BF514, B𑍴, BF518, Blackfin, gips, processor, uClinux, voiceengine, voip

Related Entries
• Rev B of Astfin’s BRI (ISDN) Asterisk Appliance Arrives -
  Apr 29, 2008
• Astfin announces Asterisk Appliance based on Blackfin -
  Oct 30, 2007
• Fonality’s trixbox appliance Part 2 -
  Mar 19, 2007
• Fonality launches Asterisk-based trixbox Appliance -
  Mar 18, 2007
• Mobile VoIP Challenges -
  Oct 20, 2008
• TMC & Digium Announce Registrations open for Digium|Asterisk World -
  Oct 20, 2008
• AsteriskNOW 1.5 beta released -
  Oct 15, 2008
• Global IP Solutions Launches Video Calling for Windows Mobile Phones -
  Oct 13, 2008
• TMC & Digium Partner for Digium|Asterisk World at ITEXPO -
  Oct 06, 2008
• Adtran IP 706 Review -
  Oct 01, 2008

TrackBacks
| Comments | Tag with del.icio.us | VoIP & Gadgets Blog Home | Permalink: New Blackfin Bᮋx Processor Launches

Copyright VoIP & Gadgets Blog

Original post by nafiz

Some computers are never turned off, or at least rarely see any state less active than “standby,” but others (for power savings or other reasons) need rebooting — daily, or even more often. The New York Times is running a short article which says that it’s not just a few makers like Asus who are trying to take some of the pain of waiting computers, especially laptops, to boot up. While it’s always been a minor annoyance to wait while a computer slowly grinds itself to readiness, “the agitation seems more intense than in the pre-Internet days,” and manufacturers are actively trying to cut that wait down to a more bearable length. How bearable? A “very good system is one that boots in under 15 seconds,” according to a Microsoft blog cited, and an HP source names an 18-month goal of 20-30 seconds.

Read more of this story at Slashdot.

Original post by timothy

Hugh Pickens writes “Traditional peak power hours — the time during the day when power demand shoots up — run from 4 pm to 7 pm when air conditioning begins to ramp up and people start heading for malls and home but utilities are now seeing another peak power problem evolve with a second surge that runs from about 8 pm to 9 pm when people head toward their big screen TVs and home computers. ‘It is [not] so much a peak as it is a plateau,’ says Andrew Tang, senior director of the smart energy web at Pacific Gas & Electric. ‘8 pm is kind of a recent phenomenon.’ Providing power during the peak hours is already a costly proposition because approximately 10 percent of the existing generating capacity only gets used about 50 hours a year: Most of the time, that expensive capital equipment sits idle waiting for a crisis. Efforts to reduce demand are already underway with TV manufacturers working to reduce the power consumption in LCD and plasma while Intel and PC manufacturers are cranking down computer power consumption. ‘Without a doubt, there’s demand,’ for green PC’s says Rick Chernick, CEO of HP partner Connecting Point’ adding that the need to be green is especially noticeable among medical industry enterprise customers.”

Read more of this story at Slashdot.

Original post by CmdrTaco

waderoush writes “Forcing sulfur atoms into silicon using femtosecond laser pulses creates a material called ‘black silicon′ that is 100 to 500 times more sensitive to light than conventional silicon, in both the visible and infrared spectrums, according to SiOnyx, a venture-funded Massachusetts start-up that just emerged from stealth mode. Today’s New York Times has a piece about the serendipitous discovery of black silicon inside the laboratory of Harvard physicist Eric Mazur. Meanwhile, a report in Xconomy explains how black silicon works and how SiOnyx and manufacturing partners hope to use it to build far more efficient photovoltaic cells and more sensitive detectors for medical imaging devices, surveillance satellites, and consumer digital cameras.”

Read more of this story at Slashdot.

Original post by Soulskill

An anonymous reader writes with this excerpt from MarketWatch: “A one-megaton nuclear bomb detonated 250 miles over Kansas could cripple many modern electronic devices and systems in the continental US and take out the power grid for a long time. … A solar storm similar to the one that occurred in 1859, which shorted out telegraph wires in the United States and Europe, could wreak havoc on electrical systems. Each of the above scenarios can create a powerful electromagnetic pulse that overloads electronic devices and systems. IAN staff and Frostburg State University physics and engineering professor Hilkat Soysal are teaming — through a $165,000 project recently approved by the Maryland Industrial Partnerships (MIPS) program — to create renewable energy-powered, electromagnetic pulse (EMP)-protected microgrids that could provide electricity for critical infrastructure facilities in the event of a disaster.” Also available are an EMP threat assessment (PDF) written for the US Congress and an estimation of economic impact (PDF).

Read more of this story at Slashdot.

Original post by Soulskill